Study of irregular wave run-up over fringing reefs based on a shock-capturing Boussinesq model

This paper presents the results of a parametric study of irregular wave run-up over fringing reefs using the shock-capturing Boussinesq wave model Funwave-TVD to better understand the role of fringing reefs in the mitigation of wave-driven flooding. Laboratory experiments were newly performed with a typical fringing reef profile and typical hydrodynamic conditions to validate the model. Experimental data shows irregular wave run-ups are dominated by the low-frequency motions and confirms the run-up resonant phenomenon over the back-reef slope, which has been revealed in previous numerical studies. It is demonstrated that irregular wave evolution and run-up over fringing reefs are reasonably reproduced by the present model with a proper grid size. However, the infragravity run-up height and highest 2% run-up height over the back-reef slope are under-predicted due to the underestimation of the infragravity wave height over the reef flat. The validated model was then utilized to model irregular wave transformations and run-ups under different conditions. Through a series of numerical experiments, the effects of key hydrodynamic and reef geometry parameters, including the reef flat width, water depth over the reef flat, fore-reef slope angle and back-reef slope angle, on the irregular wave run-up were investigated. Variations of spectral components of irregular wave run-ups were examined to better understand the physical process underlying the effect of each parameter.     

Lidar-aided analysis of boreal forest backscatter at Ku band

This paper analyzes the backscatter of the microwave signal in a boreal forest environment based on a Ku -band airborne Frequency-Modulated Continuous Waveform (FMCW) profiling radar—Tomoradar. We selected a half-managed boreal forest in the southern part of Finland for a field test. By decomposing the waveform collected by the Tomoradar, the vertical canopy structure was achieved. Based on the amplitude of the waveform, the Backscattered Energy Ratio of Canopy-to-Total (BERCT) was calculated. Meanwhile, the canopy fraction was derived from the corresponding point cloud recorded by a Velodyne VLP-16 LiDAR mounted on the same platform. Lidar-derived canopy fraction was obtained by counting the number of the first/ the strongest returns versus the total amount of returns. Qualitative and quantitative analysis of radar-derived BERCT on lidar-derived canopy fraction and canopy height are investigated. A fitted model is derived to describe the Ku-band microwave backscatter in the boreal forest to numerically analyze the proportion contributed by four factors: lidar-derived canopy fraction, radar-derived canopy height, the radar-derived distance between trees and radar sensor and other factors, from co-polarization Tomoradar measurements. The Root Mean Squared Error (RMSE) of the proposed model was 0.0958, and the coefficient of determination R2 was 0.912. The fitted model reveals that the correlation coefficient between radar-derived BERCT and lidar-derived canopy fraction is 0.84, which illustrates that lidar surface reflection explains the majority of the profiling /waveform radar response. Thus, vertical canopy structure derived from lidar can be used for the benefit of radar analysis.     

Parallelization of the flow-path network model using a particle-set strategy

High-performance simulation of flow dynamics remains a major challenge in the use of physical-based, fully distributed hydrologic models. Parallel computing has been widely used to overcome efficiency limitation by partitioning a basin into sub-basins and executing calculations among multiple processors. However, existing partition-based parallelization strategies are still hampered by the dependency between inter-connected sub-basins. This study proposed a particle-set strategy to parallelize the flow-path network (FPN) model for achieving higher performance in the simulation of flow dynamics. The FPN model replaced the hydrological calculations on sub-basins with the movements of water packages along the upstream and downstream flow paths. Unlike previous partition-based task decomposition approaches, the proposed particle-set strategy decomposes the computational workload by randomly allocating runoff particles to concurrent computing processors. Simulation experiments of the flow routing process were undertaken to validate the developed particle-set FPN model. The outcomes of hourly outlet discharges were compared with field gauged records, and up to 128 computing processors were tested to explore its speedup capability in parallel computing. The experimental results showed that the proposed framework can achieve similar prediction accuracy and parallel efficiency to that of the Triangulated Irregular Network (TIN)-based Real-Time Integrated Basin Simulator (tRIBS).     

基于高斯烟羽模型的船舶尾气扩散研究

为有效对港区大气污染进行治理、分析船舶尾气,本文详细介绍了一种基于高斯烟羽模型,通过MATLAB模拟仿真模型,其包括实验仿真过程、技术原理及理论模型对船舶尾气扩散进行的研究。该模型是在传统的高斯烟羽模型的基础上,通过对实源像源进行加权选择输入参数;通过矢量合成确定了气体扩散的方向,利用合成后的"风速"进行计算仿真,有效模拟了船舶尾气在港区或者海洋环境中的气体扩散模型。其模型简单且可以有效模拟船舶尾气扩散。并且进一步对后续模型的精确优化进行分析。     

典型深街谷内树木空间配置对行人呼吸高度处气流的影响

为揭示树木的不同空间配植方案对行人呼吸高度气流的影响,本文将树木视为均匀多孔介质,通过附加源项法从空气动力学角度用CFD模拟了H/W=2的典型深街谷几何内4种树木配植情景,实验表明,不同空间配置下树木对街谷内行人呼吸高度处局地气流的影响强弱在空间分布模式上差异悬殊：① 均匀种植的树木对街谷内行人呼吸高度的气流起到阻碍作用,不均匀种植则有效提升街谷的整体流速。4种空间配植方案下树木对气流的影响程度不同,阻碍作用从大到小的顺序为均匀间距8 m（Spa8m）>均匀间距6 m（Spa6m）>均匀间距20 m（Spa20m）>不均匀配植（Non-uniform）;对应的平均气流增强指标顺序为$\bar{D}_{spa8}$（-19.31%）<$\bar{D}_{spa6}$（-16.14%）<$\bar{D}_{spa20}$（-10.73%）<$\bar{D}_{non-uniform}$（1.25%）。② 对比不均匀和均匀的种植方案,不均匀植树的街谷内部行人呼吸高度的气流流速比其对照案例（均匀植树Spa8m方案）整体增强了106.49%。街谷中部不种树,在街谷两端配置树木并预留足够的自由空间的不均匀植树方案,能够让角涡渗入街谷中部,促使街谷内部的垂直漩涡和两端的水平角涡运动,增强湍流和垂直交换,有效减少了街道两端“风口效应”和街道中部“风影效应”的区域,改善了整个街谷行人呼吸平面的风环境。④ 合理空间配置的树木能够改善街谷内部的行人风环境。街谷内行人呼吸高度处的气流对局地条件很敏感,树木的局部配置（空间簇集、密度）将引起强烈的空间变化。在既有城市建筑布局条件下,如何通过谨慎的景观设计,利用树木等城市绿化措施有效地改善城市的行人风环境,缓解污染扩散、疾病传播等问题,本文的方法可提供一定的参考。     

非线性波消波及波场分布研究

本文基于雷诺平均N-S方程,并结合RNG k-e方程建立了粘性数值波浪水槽,对不同波陡、不同相对水深、不同相对波高的非线性规则波的阻尼消波问题和波场分布进行研究。文中提出了两种描述消波区内部阻尼变化的阻尼函数,分别适用于小波陡情形和高波陡情形。研究结果表明,小波陡组消波区可设为一个波长,阻尼系数取10~4～10~5即可满足消波要求,计算结果与实验结果及造波理论吻合良好;高波陡组消波区可设为两个波长,阻尼系数取10~4～10~5亦可满足消波要求,计算结果与实验结果吻合良好。此外,当波陡较小时,波场内反射情况的小幅改变即可对整个波场造成影响,特别是当水深较浅时这种影响极为明显,需谨慎考虑。当波陡较大时,水波能量较高,整个波场沿水波传播方向可观测到明显的衰减现象,在具体试验中需进行考虑。     

Bearing capacity of offshore umbrella suction anchor foundation in silty soil under varying loading modes

Considering the current disadvantages of present offshore wind turbine foundations, a novel anchor foundation with skirt and branches is proposed, called offshore umbrella suction anchor foundation (USAF). A series of experiments and numerical simulations were performed to explore the bearing capacity of the USAF under various kinds of loading modes. The bearing characteristics and the anchor–soil interactions are described in detail for horizontal static loading, horizontal cyclic loading, and an antidrawing (pullout) test in silty soil. In the static loading test, the load–deflection of the anchor under step loading was analyzed and the normalized curve of the load–deflection was obtained to determine the ultimate horizontal bearing capacity of the anchor under normal working conditions. Under horizontal cyclic loading, the relationship between the plastic cumulative deformation and cyclic number was determined. In addition, the responses of USAF were investigated for a low wave frequency and storm surges. In the drawing test, it was found that a “segmentation phenomenon” occurred during the test. Moreover, a method to identify the maximum antidrawing load of USAF was provided based on dynamic mechanics. The numerical results show that the use of anchor branches and skirt can enhance the bearing performance of USAF to a certain degree. However, the anchor branch has a slight positive influence on the bearing performance improvement. The USAF is not only similar to a stiff short pile, but a rotation occurs. The failure envelope under composite loading (V-M) was obtained and the changes associated with changes in the aspect ratio of the internal compartment were clarified.     

利用短期静态PPP结果反演海潮负荷位移

采用香港11个GPS测站的观测资料进行1 h、2 h、3 h和4h静态PPP解算，获得4组PPP坐标序列，利用调和分析求取11个测站处8个主要分潮的负荷位移参数（振幅和相位），将其与海潮模型计算的负荷位移参数进行对比，并比较分析PPP反演值与海潮模型值改正海潮负荷信号的效果。结果表明，垂直和水平方向上，不同PPP结果反演8个分潮的负荷位移分别具有约5 mm和7 mm的差异；PPP反演8个分潮垂向负荷位移优于全球海潮模型，但水平方向上的反演效果稍弱。     

Solution for a plane strain rough‐walled hydraulic fracture driven by turbulent fluid through impermeable rock

The impact of turbulent flow on plane strain fluid‐driven crack propagation is an important but still poorly understood consideration in hydraulic fracture modeling. The changes that hydraulic fracturing has experienced over the past decade, especially in the area of fracturing fluids, have played a major role in the transition of the typical fluid regime from laminar to turbulent flow. Motivated by the increasing preponderance of high‐rate, water‐driven hydraulic fractures with high Reynolds number, we present a semianalytical solution for the propagation of a plane strain hydraulic fracture driven by a turbulent fluid in an impermeable formation. The formulation uses a power law relationship between the Darcy‐Weisbach friction factor and the scale of the fracture roughness, where one specific manifestation of this generalized friction factor is the classical Gauckler‐Manning‐Strickler approximation for turbulent flow in a rough‐walled channel. Conservation of mass, elasticity, and crack propagation are also solved simultaneously. We obtain a semianalytical solution using an orthogonal polynomial series. An approximate closed‐form solution is enabled by a choice of orthogonal polynomials embedding the near‐tip asymptotic behavior and thus giving very rapid convergence; a precise solution is obtained with 2 terms of the series. By comparison with numerical simulations, we show that the transition region between the laminar and turbulent regimes can be relatively small so that full solutions can often be well approximated by either a fully laminar or fully turbulent solution.     

Damage assessment for submarine photoelectric composite cable under anchor impact

The impact of dropped anchor on submarine photoelectric composite cables may possibly cause electrical faults, i.e. electricity and optical signal transmission failure. In order to study the impact capacity and structural impact failure mechanism, a test setup is designed originally to examine the structural and functional integrity. A detailed finite element model (FEM) is created, considering material nonlinearity and component interaction. A parametric analysis has been performed to predict the deformation of components and impact forces, under different impact velocities and collision directions. Relationships between the armor layer indentation rate and that of internal power and optical units are achieved. The impact deformation of internal entities can be evaluated intuitively by armor layer indentation. The proposed experimental and numerical methods are well correlated, suitable to assess the impact capacity of subsea power cables and assist the protection design of subsea power cables in engineering.